AIM MXS 1.2 STRADA Road Icons
The MXS 1.2 Strada is one of our most widely used dashes on tracks and roads all over the world. The MXS 1.2 Strada has a 5″ colour TFT display that offers a great visual impact. You can configure the dash to show all the information coming from the ECU, analogue /digital inputs, predefined math channels and an optional GPS Module.
The MXS 1.2 Strada is available with a choice of connection. Choose either the OBDII or K-Line CAN, depending on whether you want to connect to the vehicles ECU or OBDII port or directly to the ECU through the CAN channel.
Connecting the MXS 1.2 Strada dash to your ECU is simple. You can sample and display dozens of channels straight from the vehicles ECU. This is usually the quickest and easiest setup, needing only 2 cable connections to the ECU instead of multiple connections to analogue sensors. The sampled data depends on the actual ECU, but will typically include RPM, throttle position, (TPS), oil, air, water temperature, oil pressure, battery voltage, speed, gear, lambda value (air/fuel ratio). The list of available ECU drivers is 1000+ and is constantly being updated and upgraded.
The MXS 1.2 Strada features 1 AMP digital output configurable to be activated/deactivated depending on the value of the analogue /digital inputs or on the impulses coming from the ECU. This allows you to automatically run external systems, such as switching on/off additional lights, to activate/deactivate a cooling fan or circulation pumps when a certain event happens.
With CAN Output you can send messages directly to an existing CAN network to improve the range of vehicle control possibilities.
AiM systems analog inputs are recorded up to 1000 times per second each. You can connect and monitor all kinds of sensors, like:
- Ratiometric potentiometers
- Pressure sensors
- K-type thermocouples
… and many others, all your custom sensors included.
MXL2 available channels list
Aim Systems Also Feature Digital Inputs:
- Speed signals – From the ECU, from the GPS and from the wheel sensors.
- RPM – From the ECU or from a digital input connected to a square wave signal (8 to 50 V) or to a low voltage (from 150 to 400 V) of the coil.
- Lap signal – Lap and split times are sampled by the GPS or via optical receiver/transmitter.
An innovative AiM systems feature is its CAN2 line, managing data coming from your additional modules (i.e. ABS, traction control, infrared temperature sensors and more…).
This feature meets the requirements of a growing number of racers, as the use of additional modules is becoming quite common in a number of series.
With Aim systems you immediately get Math Channels values: the dash logger can be configured to display those values (i.e. brake bias, calculated gear) in real time.
HIGH CONTRAST TFT DISPLAY
MXS Strada is a high contrast TFT display: its visual quality is always optimal as its ambient light sensor keeps the back light at the best brightness levels. The dash is available in the “Street Icons” version needed by street users (fuel, oil, water temp., etc.)
WATCH YOUR DATA IN PRE-CONFIGURED PAGES
MXS Strada shows, together with RPM scale, all the data you need, like speed, water temperature and oil pressure, laptimes and much more…
You can choose the custom pages you wish – including up to four additional fields – among a wide library of page styles, defining which data to be shown, their end of scale and measure units. Swapping between pages is quite easy using the push buttons.
FLEXIBLE SHIFT LIGHTS AND ALARMS
The ten multicoloured RGB shift lights can be customized to your liking, defining the RPM threshold for each single gear. The same flexibility applies to the configurable RGB alarm LEDs: you can configure them in order to turn them on/off depending on analog or digital inputs, ECU values, expansion values, math channels or – optionally – GPS information.
You choose conditions and colours of the MXS Strada: select a solid alarm or flashing one – and the flashing frequency. It is also possible to configure an accompanying text message, and set the alarm priorities.
With Aim MXS Strada Car Racing Dash Display, the CAN Output you can send messages directly to an existing CAN network in order to improve the range of vehicle control possibilities.
MXS Strada features a 1 amp digital output configurable in order to be activated/deactivated depending on the value of the analog/digital inputs or on impulses coming from the ECU.
This permits to automatically run external systems, i.e. to switch on/off additional lights, to activate/de-activate a cooling fan or circulation pumps, etc. when a certain event happens. more info>
A MODULAR SYSTEMS
See Accessories Tab above for range of available expansions
Add expansion modules via our built in CAN bus eg. GPS08, external Memory Modules, Channel Expansions, Lambda Controllers.
These are only some of the items that can be added to our MXS Strada for incrementing the performance and the data acquired
RACE STUDIO 3 CONFIGURATION
MXS Strada is configured via Race Studio3: you can create, modify, delete, import and export configurations with all channels, ECU drivers, Math channels, Display Pages, Digital output, Alarms, Shift Lights and all the expansions you need.